DecorFlex Glue cement-dispersive glue
DecorFlex Glue cement-dispersive glue
DecorFlex Glue cement-dispersive polystyrene glue
Two components glue is used to mount coated decorative EPS and XPS profiles.
Characterized by high adhesion and flexibility.
For outdoor use.
Ingredient A (1kg) it is wet mix + Ingredient B (3 kg) it is dry mix.
| DecorFlex Glue | |
| Description | 2-component cement-dispersive polystyrene glue |
| Order code | A-CD4 |
|
Colour |
grey |
|
Packages |
3 kg + 1 kg |
|
Origin |
Made in EU |
|
Component B: |
|
|
Bulk density [g/cm3] |
1,65 |
|
Moisture content [% m/m] |
0,1 |
|
Component A: |
|
|
Density [g/cm3] |
1,01 |
|
Content of non-volatile substances [% m/m] |
31,0 ± 0,2 |
|
pH |
7,9 |
|
Time flow out of the cup with conical bottom nozzle diameter 2 mm [s] |
52 |
|
Ingredient A and B after mixing: |
|
|
Open time [h] |
0,75 |
|
Ability of wetting expanded polystyrene (APT) |
compatible |
Adhesion
| Weld
adhesive, group attached with glue (Grip team, styrofoam fixed glue to the ground concrete) [MPa] |
|
| - after 24 hours | 0,15 |
| - after 48 hours | break in polystyrene foam |
| - after 28 days | break in polystyrene foam |
| - after 2 hours of soaking in water | break in polystyrene foam |
| - after 25 cycles of freezing and thawing | break in polystyrene foam |
| Adhesion after 28 days of ceramic tiles attached with glue [MPa] | 3,8 |
| The flexibility of the adhesive joints [mm] | 30 |
| The relative diffusion resistance of the adhesive joints [m] | 0,8 |
| Resistance on exposure to temperature variables for 25 cycles, the behavior of pin connectors | no change |
| Capillary pull up [kg/m2*24 h] | 0,22 ± 0,04 |
| Resistance to impact a hard mass with armed mesh with thermal insulation [cm] | 100 no change |
| The strength of adhesive joints on picking off the ground the concrete, air drying weld in 5°C [MPa] | 3,5 |
| The strength of adhesive joints on picking off the ground the concrete, air drying weld in 20°C [MPa] | 3,9 |
Certification
DecorFlex Glue was tested by The Centre of Research and Development - Paints, Adhesives and Polymers SPEKTROCHEM in accordance with the methodology of their research for determining the quality of adhesives for the attachment of decorative stucco styrofoam. Studies suggest that it complies with the provisions of declared parameters and is useful for mounting of decorative polystyrene moldings.
Spektrochem clearance No. S-75/2012.
How to apply
Prior to use add the component A to the component B. Miix it manually or by a drilling machine. Wait 5-10 minutes and mix again.
The adhesive should be applied undiluted by using your putty knife or trowel
stainless steel.
The work done at the base and ambient temperature of 10-30 o C on not
sunny surface, days free from rain and fog. Clean tools with tap water
immediately after finishing the work.
Storage
In its original packaging the product retains its properties for 6 months
from the date of manufacture. Keep at a temperature of 10-40 oC in factory
sealed packages.
Protect from frost and excessive sun exposure !
Safety
Xi Irritant product.
S2 Protect from children.
S22 Do not breathe dust.
S26 Contaminated with the eyes, rinse immediately with plenty of water and seek
medical advice.
S46 If swallowed, immediately seek medical advice - show label and packaging.
S36/37/39 Wear suitable protective clothing, gloves and eye or face protection.
Preposlať mailom
Tlač stránky